GLExec Epilogue Functionality

Starting from version 0.9 gLExec can optionally run an epilogue executable after the payload has finished.

General

In linger mode, gLExec can optionally run a trusted executable, intended to clean up the payload environment. The option should point to the absolute path of a trusted executable: it must not be possible for anyone except the root user (or the epilogue_user and/or members of the epilogue_group when set) to change the executable. It will run as uid/gid 0,0 (unless epilogue_user and/or epilogue_group are set). If it does not finish within a set epilogue_timeout, it will be send a SIGTERM. For proper functioning it is advised that gLExec will do the userswitch (instead of LCMAPS).

If the epilogue fails for whatever reason, gLExec will return either with a 202 exit code (internal gLExec error) or potentially a 204 (e.g. when the epilog itself returned a 201-204 range exit code).

Configuration options

The epilogue can be configured using the glexec.conf settings

epilogue	when set, the name of the trusted binary or script to run. Needs to be a absolute canonical path
epilogue_user	When set, the epilogue will be run with this user identity. In addition this user is allowed to have write permission for the epilogue executable (i.e. is trusted). This option can only be used when gLExec does the userswitch. Default: root.
epilogue_group	When set, the epilogue will be run with this group identity. In addition members of this group are allowed to have write permission for the epilogue executable (i.e. are trusted). When unset, the executable will be run with GID 0 and no group will be trusted. This option can only be used when gLExec does the userswitch.
epilogue_timeout	The epilogue executable will run for at most this timeout in seconds, before being sent a SIGTERM (and SIGKILL). Default: 300 seconds.

Runtime Environment

The epilogue runs with the same cleaned environment as gLExec sets up for the payload, with a number of additional variables, all starting with GLEXEC_EPILOG_. Any variables setup before gLExec starting with GLEXEC_EPILOG_ will be cleared before the epilogue is run.

GLEXEC_EPILOG_ARGV<N>	argv of payload
GLEXEC_EPILOG_GLEXEC_USER	calling user username
GLEXEC_EPILOG_GLEXEC_GROUP	calling user's primary groupname
GLEXEC_EPILOG_GLEXEC_UID	calling user's uid
GLEXEC_EPILOG_GLEXEC_GID	calling user's primary gid
GLEXEC_EPILOG_GLEXEC_SGIDS	calling user's secondary gids, colon separated
GLEXEC_EPILOG_TARGET_USER	target user's username
GLEXEC_EPILOG_TARGET_GROUP	target user's primary groupname
GLEXEC_EPILOG_TARGET_UID	target user's uid
GLEXEC_EPILOG_TARGET_GID	target user's primary gid
GLEXEC_EPILOG_TARGET_SGIDS	target user's secondary gids, colon separated
GLEXEC_EPILOG_GLEXEC_PID	lingering gLExec process ID
GLEXEC_EPILOG_GLEXEC_SID	lingering gLExec session ID
GLEXEC_EPILOG_GLEXEC_PGID	lingering gLExec process group
GLEXEC_EPILOG_TARGET_PID	payload process ID
GLEXEC_EPILOG_TARGET_PGID	payload process group
GLEXEC_EPILOG_TARGET_RC	payload exit code

Security

• In order to prevent tampering with the epilogue binary or script, the permissions need to be such, that only the root user and optionally epilogue user, has write access to the file or one of its path members (it is "trusted-root").
• GLExec becomes immune to signals from any user but root.
• It is important to note that writing a epilogue should be done with utmost care, as it will be ran (normally) by root user and triggered automatically.