Difference between revisions of "FELIX instructions for Petals"
m |
m (add commands) |
||
| Line 1: | Line 1: | ||
[[DAQ systems|''Back to DAQ systems'']] | [[DAQ systems|''Back to DAQ systems'']] | ||
| + | |||
| + | |||
| + | How to configure a petal (instructions taken from DESY repo https://gitlab.cern.ch/desy-atlas/itk/petal-testing): | ||
''cd'' into the ''petal-testing'' directory and then execute the following commands: | ''cd'' into the ''petal-testing'' directory and then execute the following commands: | ||
| − | <code>source dependencies/setupFELIX.sh</code> | + | Setup the FELIX dependencies: <code>source dependencies/setupFELIX.sh</code> |
| + | |||
| + | Initialize the FLX card <code>flx-init</code> | ||
| − | <code>flx- | + | Invert the polarity (for lpGBTv1): <code>flx-config set GBT_RXPOLARITY=0xFFFFFFFF</code> |
| − | <code>flx- | + | Verify the status of the PODs: <code>flx-info POD</code> |
| − | <code>flx-info | + | Check that all connected links are aligned: <code>flx-info GBT</code> |
| − | + | If testing the PPB R5 Vancouver Petal: | |
| − | <code>source configs/elinks/elinks_petal_R5_640Mbs.sh</code> | + | Configure the ''elinks'' on your FELIX card: <code>source configs/elinks/elinks_petal_R5_640Mbs.sh</code> |
| − | <code>elinkconfig</code | + | Check your config: <code>elinkconfig</code> Click on ''Read Cfg'', then you can ''Quit'' |
| − | <code>fice -G0 -I71 configs/lpgbt/lpgbt_PT_M_LH_V1_Pri_hex.cnf</code> | + | Push the lpGBT config to the petal chipset: <code>fice -G0 -I71 configs/lpgbt/lpgbt_PT_M_LH_V1_Pri_hex.cnf</code> |
| − | <code>fice -G0 -I71 -C configs/lpgbt/lpgbt_PT_M_LH_V1_Pri_hex.cnf</code> | + | Verify this has worked (you should see the line "Compared 336 values, found 0 differences"): <code>fice -G0 -I71 -C configs/lpgbt/lpgbt_PT_M_LH_V1_Pri_hex.cnf</code> |
| − | <code>startFelixcore</code> | + | Start FELIXCore and don't close this terminal: <code>startFelixcore</code> |
Revision as of 14:14, 15 May 2024
How to configure a petal (instructions taken from DESY repo https://gitlab.cern.ch/desy-atlas/itk/petal-testing):
cd into the petal-testing directory and then execute the following commands:
Setup the FELIX dependencies: source dependencies/setupFELIX.sh
Initialize the FLX card flx-init
Invert the polarity (for lpGBTv1): flx-config set GBT_RXPOLARITY=0xFFFFFFFF
Verify the status of the PODs: flx-info POD
Check that all connected links are aligned: flx-info GBT
If testing the PPB R5 Vancouver Petal:
Configure the elinks on your FELIX card: source configs/elinks/elinks_petal_R5_640Mbs.sh
Check your config: elinkconfig Click on Read Cfg, then you can Quit
Push the lpGBT config to the petal chipset: fice -G0 -I71 configs/lpgbt/lpgbt_PT_M_LH_V1_Pri_hex.cnf
Verify this has worked (you should see the line "Compared 336 values, found 0 differences"): fice -G0 -I71 -C configs/lpgbt/lpgbt_PT_M_LH_V1_Pri_hex.cnf
Start FELIXCore and don't close this terminal: startFelixcore