Difference between revisions of "TVModularAnalysis"
Jump to navigation
Jump to search
m |
m |
||
| Line 1: | Line 1: | ||
| − | + | ===define_sample=== | |
| − | |||
The <tt>ls -1 $DIR/*.root</tt> command it used is unable to cope with very large. Replacing it with <tt>find $DIR -name '*.root'</tt> seems to do the trick. | The <tt>ls -1 $DIR/*.root</tt> command it used is unable to cope with very large. Replacing it with <tt>find $DIR -name '*.root'</tt> seems to do the trick. | ||
| − | + | ||
| + | ===b-tagging=== | ||
<pre> | <pre> | ||
In case you're using the Nikhef TVNtuples, you should add || (FullReco0-> | In case you're using the Nikhef TVNtuples, you should add || (FullReco0-> | ||
| Line 33: | Line 33: | ||
</pre> | </pre> | ||
| − | + | ===Isolation cuts=== | |
If you like to have the same cuts as TopView, you should change in | If you like to have the same cuts as TopView, you should change in | ||
MuonSelection.C to etcone20 and the cut to 6 GeV, but that is up to you... | MuonSelection.C to etcone20 and the cut to 6 GeV, but that is up to you... | ||
| − | |||
| − | |||
Revision as of 12:23, 18 July 2007
define_sample
The ls -1 $DIR/*.root command it used is unable to cope with very large. Replacing it with find $DIR -name '*.root' seems to do the trick.
b-tagging
In case you're using the Nikhef TVNtuples, you should add || (FullReco0->
vPJet_weight(i_jet) > 4.5 && FullReco0->vPJet_p_T(i_jet)>20000) in the
FillAODVectors module in TVModularAnalysis, like here:
//--------------------------------------
void FillAODVectors::fillBJetVec(){
//--------------------------------------
//----------------------------------------------------------------------
// Fill Vectors of TLorentzVectors-with-index for 'all' and 'good' Bjets
//----------------------------------------------------------------------
vector<TLorentzVectorWIdx>& BJetVec = gList["BJetVec"] ;
BJetVec.clear();
for(Int_t i_jet = 0; i_jet<FullReco0->PJet_N; i_jet++){
if(FullReco0->vPJet_BTagged(i_jet)==1 || (FullReco0->vPJet_weight(i_jet) >
4.5 && FullReco0->vPJet_p_T(i_jet)>20000) ){
TLorentzVectorWIdx v(FullReco0->vPJet_px(i_jet),FullReco0->vPJet_py
(i_jet),FullReco0->vPJet_pz(i_jet),FullReco0->vPJet_E(i_jet),i_jet);
BJetVec.push_back(TLorentzVectorWIdx(FullReco0->vPJet_px
(i_jet),FullReco0->vPJet_py(i_jet),FullReco0->vPJet_pz(i_jet),FullReco0->
vPJet_E(i_jet),i_jet) );
}
}
}
Otherwise you don't have any b-jets, because the BTagged variable was not
filled. In case of the centrally produced 'Akira' Ntuples it will work just
fine the way it is now though.
Isolation cuts
If you like to have the same cuts as TopView, you should change in
MuonSelection.C to etcone20 and the cut to 6 GeV, but that is up to you...