Difference between revisions of "Upgrade/RadiationTestBirmingham"
Jump to navigation
Jump to search
| Line 2: | Line 2: | ||
* A: glue mechanics tests (see picture) | * A: glue mechanics tests (see picture) | ||
| − | * number of samples: three (different types of glue) | + | * number of samples: three (different types of glue: StycastFT2850, EP37-3FLFAO, Polytec TC423) |
* assembly: titanium (1.8mm), adhesive, 0.2mm), silicon (0.5 mm) | * assembly: titanium (1.8mm), adhesive, 0.2mm), silicon (0.5 mm) | ||
* size: 42mm x 14mm x 2.5mm | * size: 42mm x 14mm x 2.5mm | ||
| Line 9: | Line 9: | ||
* B: glue heat conductivity tests (see picture) | * B: glue heat conductivity tests (see picture) | ||
| − | * number of samples: three (different types of glue) | + | * number of samples: three (different types of glue: StycastFT2850, EP37-3FLFAO, Polytec TC423) |
* assembly: aluminium (2mm), adhesive (10mm), aluminium (2mm) | * assembly: aluminium (2mm), adhesive (10mm), aluminium (2mm) | ||
* size: 12mm x 14mm x 2mm | * size: 12mm x 14mm x 2mm | ||
| Line 16: | Line 16: | ||
* C: RF box coating tests (see picture) | * C: RF box coating tests (see picture) | ||
| − | * number of samples: three (different types of coating) | + | * number of samples: three (different types of coating: Torlon, Polyurethane, XXX) |
* assembly: aluminium (1mm) on both sides covered with very thin layer of coating | * assembly: aluminium (1mm) on both sides covered with very thin layer of coating | ||
* size: minimally 1x1cm (size can b increased, if that makes it easier to handle samples) | * size: minimally 1x1cm (size can b increased, if that makes it easier to handle samples) | ||
* desired radiation load: 1x10^16 1-MeV-neutron equivalent / cm^2 | * desired radiation load: 1x10^16 1-MeV-neutron equivalent / cm^2 | ||
* radiated surface: ideally over entire surface, but probably a 'spot' profile is acceptable as well | * radiated surface: ideally over entire surface, but probably a 'spot' profile is acceptable as well | ||
Revision as of 11:47, 7 June 2017
Three types of samples:
- A: glue mechanics tests (see picture)
* number of samples: three (different types of glue: StycastFT2850, EP37-3FLFAO, Polytec TC423) * assembly: titanium (1.8mm), adhesive, 0.2mm), silicon (0.5 mm) * size: 42mm x 14mm x 2.5mm * desired radiation load: 2x10^15 1-MeV-neutron equivalent / cm^2 * radiated surface: preferable entire surface (too large?)
- B: glue heat conductivity tests (see picture)
* number of samples: three (different types of glue: StycastFT2850, EP37-3FLFAO, Polytec TC423) * assembly: aluminium (2mm), adhesive (10mm), aluminium (2mm) * size: 12mm x 14mm x 2mm * desired radiation load: 2x10^15 1-MeV-neutron equivalent / cm^2 * radiated surface: over the adhesive layer
- C: RF box coating tests (see picture)
* number of samples: three (different types of coating: Torlon, Polyurethane, XXX) * assembly: aluminium (1mm) on both sides covered with very thin layer of coating * size: minimally 1x1cm (size can b increased, if that makes it easier to handle samples) * desired radiation load: 1x10^16 1-MeV-neutron equivalent / cm^2 * radiated surface: ideally over entire surface, but probably a 'spot' profile is acceptable as well